Heating and Cooling

Air Conditioner Not Cooling: 7 Checks Before You Call a Tech

The AC runs but the room stays warm. Seven causes, from a clogged filter to a frozen coil, and the one repair you must never attempt yourself.

An air conditioner that runs without cooling is one of the most common summer calls, and a large share of them are airflow problems that cost nothing to fix. The unit has three jobs: pull heat out of the indoor air, move that heat outside, and move enough air to do both. When any of those breaks, you get cool-ish air, weak airflow, or a unit that runs forever.

Work through the free checks first. Refrigerant work requires a license, gauges, and a recovery machine, and no guide should walk you through it.

Before you touch anything

Turn off the unit at the thermostat and the breaker before opening any panel. The outdoor condenser has a capacitor that holds a lethal charge after power is removed.

Do not add refrigerant or “top off” the system. Refrigerant is not a consumable; a system that is low has a leak, and adding gas without finding the leak is both illegal in many places and wasteful.

Do not hose down a running condenser. Water on live electrical parts and a spinning fan is a shock and damage risk.

If the indoor coil is frozen into a block of ice, turn the system off at the thermostat and let it thaw completely before running it again. Running a frozen coil can damage the compressor.

1. The air filter is clogged

A dirty filter starves the indoor coil of air, the coil gets cold and ices up, and the unit stops moving heat. This is the first thing to check on any AC that is not cooling.

How to test it: Hold the filter to a light. If you cannot see through it, it is clogged. Check the return grille filter and any filter at the air handler.

What it means: Replace it. Filters should be changed every one to three months, monthly during heavy use or in a house with pets. This is the cheapest AC maintenance there is.

2. The outdoor condenser coil is dirty or blocked

The outdoor unit dumps heat into the air. When the coil is packed with cottonwood fluff, grass, or dust, or when shrubs and debris block the airflow, the unit cannot reject heat and cooling collapses.

How to test it: Look at the coil fins. If you cannot see through them, they are blocked. Check that the unit has two feet of clear space around it and that nothing is sitting on top.

What it means: Rinse the coil with a garden hose from inside out, with the power off. Clear the vegetation. Do not use a pressure washer; it flattens the fins.

3. The indoor coil is frozen

A frozen indoor coil means the system has been running with restricted airflow or low refrigerant. You will see ice on the copper lines or water dripping from the air handler.

How to test it: Look at the indoor coil and the large suction line. Frost or ice on the line is definitive. Turn the system off and let it thaw for several hours with the fan running in fan-only mode.

What it means: If the coil freezes with a clean filter, the likely cause is low refrigerant from a leak. That is a technician diagnosis, not a DIY one. Do not keep resetting a system that freezes.

4. The blower is not moving enough air

A weak blower produces cool air at low volume, and the house never catches up. The blower motor can fail, the capacitor can weaken, or the belt on older units can slip.

How to test it: Feel the airflow at a register. Weak, barely-there airflow with a clean filter points to the blower. Listen at the air handler for a motor that hums without spinning, which usually means a failed capacitor.

What it means: Blower capacitors are inexpensive and replaceable, but they hold a charge and the diagnosis requires a meter. If the motor itself has failed, replacement is a technician job.

5. The thermostat or the settings are wrong

Before anything else, confirm the thermostat is in cool mode, the setpoint is below room temperature, and the fan is on auto rather than a schedule. A thermostat in a schedule hold, or one with dead batteries, will not call for cooling.

How to test it: Set the thermostat to cool and lower the setpoint five degrees. Listen for the outdoor unit to start within a minute. If the indoor fan runs but the outdoor unit does not, the problem is outside or in the control.

What it means: Replace the thermostat batteries, or check the wiring at the outdoor unit’s contactor. A thermostat that never calls is a cheap fix compared to everything else on this list.

6. The outdoor unit is not running at all

If the indoor blower runs but the outdoor unit is silent, the problem is at the condenser: a tripped breaker, a failed capacitor, a burnt contactor, or a compressor that is locked out on overload.

How to test it: Check the breaker at the panel and the disconnect switch at the unit. Then listen for a click from the contactor when the thermostat calls. No click and no fan points to the control side; a click and a hum with no fan points to the capacitor or the motor.

What it means: Capacitors and contactors are common failures and inexpensive parts, but diagnosing them requires working inside a live unit. If you are not trained on AC electrical, this is the point to call.

7. The system is undersized, or the house is leaking air

Sometimes nothing is broken. A unit that cannot keep up on a 100°F day was sized for a milder climate, or the house is leaking conditioned air through gaps and old windows. The AC runs continuously and the temperature creeps up.

How to test it: Note the gap between the thermostat setpoint and the actual room temperature on a hot afternoon. A well-sized system holds within two or three degrees. A five-degree gap on design days suggests a capacity or envelope problem.

What it means: This is not a repair, it is a diagnosis for a contractor. Sealing air leaks and improving attic insulation usually does more than a bigger unit.

Quick diagnosis table

What you observeMost likely causeEffort
Weak airflow, cool airClogged filterFree
Runs constantly, outdoor unit hotDirty condenser coilLow
Ice on the indoor coil or linesFrozen coil from airflow or refrigerantLow thaw, tech diagnosis
Cool air at low volumeBlower motor or capacitorTechnician
Outdoor unit silentBreaker, capacitor, contactorTechnician
Cannot keep up on hot daysUndersized unit or air leakageContractor assessment

When to stop and call a technician

Call for refrigerant, compressors, capacitors, contactors, and blower motors. Call if the indoor coil freezes repeatedly after a filter change, if you see oil residue on the copper lines, or if the unit trips the breaker.

Stop and shut the system off if you smell a burning odor at the air handler or see scorched wiring. An AC that has been running with a failing capacitor can damage the compressor, which is the most expensive part of the system.

For a furnace that runs without heat, see furnace not blowing heat. For a water heater that stopped heating, see no hot water.

Safety first. Unplug the appliance or switch off the breaker before opening anything. If a repair involves gas piping, the main electrical panel, or sealed refrigerant, stop and call a licensed technician.