Kitchen
Dishwasher Won't Drain: Why Water Is Sitting in the Bottom
Standing water in the tub after a cycle is usually a blocked filter, a kinked drain hose, or a jammed drain pump. Here is the order to check them.
You open the dishwasher after a full cycle and there is an inch of cloudy water sitting in the bottom. The dishes on the lower rack may be clean, or they may be coated in whatever was on them when the cycle started. Either way, the machine is not emptying.
A dishwasher drains in short bursts during the cycle and again at the end, using the same small pump that recirculates water. When that path clogs or the pump stops turning, water has nowhere to go. The causes are narrow enough that you can work through them in about twenty minutes.
Before you start
Switch the breaker off, or unplug the machine if it has a cord and an accessible outlet. Water and 120-volt wiring share the same space under a dishwasher, and the drain pump sits at the lowest point where leaks collect.
Put a towel down and have a shallow pan ready. Once you open the drain path, whatever is in the tub comes out.
1. The filter and sump are clogged
Nearly every modern dishwasher has a filter assembly at the bottom of the tub: a coarse mesh, a fine mesh, and a cylindrical filter around the pump intake. Grease, seeds, glass shards, labels, and bits of food accumulate there, and once the mesh is sealed over, the pump runs but moves almost no water.
Test it: pull the lower rack out, unscrew the cylindrical filter (most models release it with a quarter turn), and lift out the mesh. Hold it up to a light. A filter that is opaque when backlit is the fault.
Clean it in warm water with a brush and a little dish soap, rinse, and reassemble exactly as it came apart. Then run a rinse-only cycle and watch whether the water disappears.
This is by far the most common cause and it is maintenance, not repair. Most manufacturers recommend cleaning the filter monthly.
2. The drain hose is kinked or blocked
The drain hose runs from the pump under the unit to the sink’s disposal or to a standpipe. Three things go wrong with it:
- Kinked: the machine was pushed back and folded the hose behind it.
- Clogged: grease and food debris build up in the corrugations, especially if the machine has been run without hot water or with heavy grease loads.
- Installed without a high loop: if the hose lies flat on the floor, water in the sink or disposal can siphon back into the tub after the cycle. This looks like a drain failure but the machine drained fine.
Test it: put the machine on its side or pull it out far enough to see the hose. Straighten kinks. If the hose feels firm in one spot, disconnect it from the sink end and push water through it into a bucket. Slow flow means a blockage.
3. The sink drain or garbage disposal is blocked
If the dishwasher drains into a garbage disposal, a disposal with food clogging it will back water into the dishwasher, because the dishwasher’s drain has nowhere to discharge. The same applies if the sink drain itself is slow.
Test it: run water in the sink and see whether it drains at normal speed. Fill the sink a few inches, then run the disposal and watch the level. If the sink backs up or drains sluggishly, the problem is the sink plumbing, not the dishwasher.
On a disposal, the classic issue is a plugged dishwasher inlet: when a new disposal is installed, the plug in the inlet port is sometimes left in place, and the dishwasher has never drained properly since.
4. The air gap or check valve is blocked
Homes plumbed with an air gap on the sink deck (a small chrome fitting next to the faucet) can get the air gap clogged with food debris. When that happens, water cannot leave the dishwasher even though the pump is working.
Test it: remove the air gap cap and cover, and check the small chamber for debris. Clear it and run the cycle again. If the air gap has been leaking onto the counter, that is the same blockage showing up from the other side.
5. The drain pump is jammed or dead
If the filter is clean, the hoses are clear, and the sink drains fine, the pump is the remaining suspect. Drain pumps fail because debris jams the impeller, or because the motor winding dies.
Test it: start a cycle and listen at the bottom of the machine during the first drain. A working pump produces a low whirr. Silence during the drain phase means no power or a dead motor. A hum with no water movement means a jammed impeller.
On many models the drain pump is accessible from inside the tub once the filter assembly is removed, and glass or a bone can be pulled out with needle-nose pliers. On others the pump is reached from below, which means tipping the machine.
If the pump is dead, replacement is a moderate job: usually 45 to 90 minutes and one part, matched to the model number. Expect the part to cost less than a service call.
6. The control board is not commanding the drain
The last possibility is electrical. If the pump receives no voltage when it should, the board or a relay is the cause. This is the point where a multimeter and the service manual for your model matter more than general advice.
Test it: with the machine unplugged, check the pump’s harness for continuity and look for scorched connector pins. A burnt connector is a common failure on machines more than eight years old, and it often costs less to replace the connector than the board.
Diagnostic summary
| Symptom | Most likely cause | Effort |
|---|---|---|
| Water present, cycle otherwise completes | Clogged filter or sump | 20 min |
| Water backs up when sink runs | Sink or disposal blockage | Plumbing |
| Machine never drained since install | Disposal inlet plug still in place | 15 min |
| Water drains, then returns | Missing high loop or siphon | 20 min |
| Pump silent during drain | Dead pump or no power | 45–90 min |
| Pump hums, no flow | Jammed impeller | 30–60 min |
| Leak from air gap | Blocked air gap | 15 min |
When to stop and call a technician
- Water is leaking from under the machine, not just sitting in the tub. A leaking tub or pump seal needs the unit opened up.
- The machine trips the breaker when the drain starts. That is an electrical fault, not a clog.
- The unit is built in under a counter with a fixed connection and no shutoff within reach.
If the dishwasher is more than twelve years old and needs both a pump and a control board, the arithmetic usually favors replacement. A drain pump alone is worth repairing on almost any machine.
If your problem is a washer rather than a dishwasher, the drain path is different but the logic is the same; the washing machine drain guide walks through it step by step.