Plumbing
Faucet Dripping: How to Fix a Leaky Tap in Under an Hour
A drip every few seconds wastes thousands of gallons a year. Identify whether it is a cartridge, a washer, or a valve seat, then replace the part.
A dripping faucet is annoying, wasteful, and almost always fixable with a ten-dollar part. A tap that drips once per second wastes around 3,000 gallons a year, and in a house with hard water the drip is usually the first sign that a cartridge or a washer has worn out.
The repair depends on the type of faucet. Compression faucets use washers and seats. Single-handle and two-handle ceramic or cartridge faucets use cartridges. Knowing which you have decides which part you buy.
Before you touch anything
Shut off the water supply. Under the sink there are usually two shut-off valves, one for hot and one for cold. Close both and open the faucet to release pressure.
Plug the drain with a rag so small parts cannot fall in. Cartridge pieces and screws are easy to lose and hard to retrieve.
Do not force a corroded valve or a stuck cartridge. Penetrating oil and a little patience beat a snapped stem, which turns a one-hour job into a plumber’s visit.
1. The cartridge is worn (single-handle faucets)
Most modern kitchen and bathroom single-handle faucets use a cartridge that mixes hot and cold. The cartridge has seals that wear against the valve body. When they go, water seeps past and drips from the spout.
How to test it: The drip continues after you shut off both supply valves and reopen them, and the handle feels loose or requires more travel to shut off completely. If the drip stops when the handle is pressed harder, the cartridge is worn.
What it means: Remove the handle, the retaining ring, and pull the cartridge out. Take it to the store to match; there are dozens of variants. Installation is the reverse, and a new cartridge usually fixes the drip entirely.
2. The washer or the seat has worn (compression faucets)
Old two-handle compression faucets use a rubber washer against a metal seat. The washer hardens and the seat can corrode or pit, and water finds the gap.
How to test it: The faucet drips from one spout only, and turning that handle harder slows or stops it. Removing the stem shows a flattened or cracked washer.
What it means: Replace the washer, and inspect the seat with a flashlight. A pitted seat needs re-seating with a seat wrench, which is a $10 tool. If the seat is badly corroded, replace the faucet.
3. The valve seat or the diverter has failed
Some faucets have a diverter that switches between the spout and a sprayer. A failed diverter leaks internally and shows up as a drip from the sprayer or the spout when the faucet is off.
How to test it: Dry the sprayer, then watch it for a drip with the faucet off. A drip at the sprayer with the faucet off points to the diverter.
What it means: Diverter replacement varies by model. Many are a push-in part; some require removing the spout. Check the parts diagram for your model before starting.
4. The aerator or the sprayer head is leaking
A drip from the aerator threads, or water running from the sprayer when the faucet is off, can be a worn aerator washer or a sprayer head that has failed.
How to test it: Dry the aerator and the sprayer, then watch. A drip at the base of the aerator means its washer is worn.
What it means: Replace the aerator washer or the aerator. Sprayer heads are often replaceable as a unit, which is easier than rebuilding one.
5. The supply line or the shut-off valve is the source
Sometimes the drip is not the faucet at all. A shut-off valve that does not close fully, or a supply line that seeps, produces water under the sink that people attribute to the faucet.
How to test it: Dry everything under the sink and check after an hour with the faucet off. Water at the valve or the line identifies the real source.
What it means: Replace the shut-off valve or the supply line. Braided lines are inexpensive and last longer than the plastic ones.
6. High water pressure is shortening part life
Pressure above 80 psi stresses cartridges and washers and causes repeated failures. If you have replaced a cartridge twice in two years, pressure is probably the reason.
How to test it: A hose-bib pressure gauge tells you the house pressure. Anything over 80 psi is worth correcting.
What it means: Install a pressure-reducing valve at the main. It protects the faucets, the water heater, and the appliances.
Quick diagnosis table
| What you observe | Most likely cause | Effort |
|---|---|---|
| Single-handle faucet drips, handle loose | Cartridge | Low |
| Two-handle faucet drips from one spout | Washer or seat | Low |
| Sprayer drips with faucet off | Diverter | Medium |
| Drip at the aerator base | Aerator washer | Free |
| Water under the sink, faucet dry | Supply line or shut-off | Low |
| Repeated cartridge failures | House pressure | Plumber |
When to stop and call a plumber
Call a plumber if the shut-off valve will not close, if the faucet body is cracked, or if the valve seat is corroded beyond re-seating. Call also for a wall-mounted faucet or a concealed valve, which usually requires opening the wall.
Stop if water is coming from inside the wall rather than from the fixture. That is a supply pipe issue and a much bigger repair.
One tip that saves repeat work: when you replace a cartridge, clean the valve body and apply plumber’s grease to the new cartridge’s seals. It extends the life of the part and makes the handle turn smoothly.
Related reading
For a toilet that runs continuously, see toilet running constantly. For water under a water heater, see water heater leaking.