Heating
Furnace Runs but No Heat: Blowing Cold Air? Check These 6 Things
The blower runs, the thermostat calls for heat, and the air is cold. Six causes, including the flame sensor that stops most furnaces from firing.
A furnace that runs its blower but never produces warm air is a specific failure and, on a gas furnace, often a single inexpensive part. The blower running means the control board is alive and the thermostat is asking for heat. What is missing is the burner.
Do not treat this as a general HVAC problem. Furnaces involve gas, a heat exchanger, and a flue, and three of those can kill you if handled wrong. The checks below stay on the safe side of the burner compartment: filter, flame sensor, igniter, condensate, and airflow.
Before you touch anything
If you smell gas, leave the house and call the gas utility from outside. Do not flip switches, do not use a phone inside.
Turn the furnace off at the switch and the breaker before opening the burner compartment. There is 120-volt power inside, and the igniter gets red hot.
Do not open the heat exchanger or the flue, and do not bypass the pressure switch or the roll-out sensors. Those devices exist because a cracked heat exchanger can put carbon monoxide into the supply air.
Replace the filter before anything else. It is the cheapest step and it eliminates a whole class of problems.
1. The air filter is clogged
A dirty filter restricts airflow, and many furnaces protect themselves by limiting the burn or shutting down on a high-limit switch. The blower keeps running, the air is cool, and the furnace short-cycles.
How to test it: Hold the filter up to a light. If you cannot see through it, replace it. Check the filter’s MERV rating against the furnace’s maximum; too high a rating restricts airflow just as badly as a dirty filter.
What it means: Change the filter every one to three months. This single habit prevents a lot of service calls, and it is the first thing any technician checks.
2. The flame sensor is dirty
The flame sensor is a metal rod in the burner flame path. It proves the flame is lit; if it does not sense flame within a few seconds, the control shuts the gas valve to prevent unburned gas from filling the heat exchanger. A sensor coated with a thin oxide layer stops working even though the burner lights.
How to test it: Watch the ignition sequence. Burners light, then go out after three to five seconds, and the board may retry two or three times before locking out. That pattern is almost always the flame sensor.
What it means: Clean the sensor with fine steel wool or a dollar bill, never sandpaper, and reinstall. This fixes the majority of these calls. If it recurs every season, replace the sensor; they are inexpensive.
3. The hot surface igniter is weak or broken
The igniter glows to light the burners. A cracked igniter does not glow at all. A weak one glows but does not get hot enough to light the gas, and the board locks out after a few attempts.
How to test it: Watch the igniter during a call for heat. It should glow bright orange within 30 to 60 seconds. No glow, or a dull red glow, means it needs replacement. Do not touch the igniter with bare fingers; the oils shorten its life.
What it means: Igniter replacement is a common DIY repair, but the part is fragile and model-specific. Handle it with gloves and match the part number.
4. The condensate drain is blocked (high-efficiency furnaces)
A 90-percent-plus furnace condenses water out of the flue gas. That water drains through a trap and a tube, and if the trap clogs or freezes, a pressure switch opens and the furnace refuses to fire. The blower still runs.
How to test it: Look for standing water in the condensate trap, and check the drain tube for kinks or ice. In cold weather, a drain that runs outside can freeze and block the furnace.
What it means: Clear the trap and the tube with warm water. If the drain discharges outdoors, reroute it to an indoor drain or add freeze protection.
5. The pressure switch or the inducer is failing
Before ignition, the furnace runs a draft inducer fan and confirms airflow with a pressure switch. A weak inducer motor or a clogged pressure switch port stops the sequence before the burners ever light, and the blower may still run.
How to test it: Listen at the start of a call for heat. You should hear the inducer fan spin up before the igniter glows. No fan, or a fan that sounds rough, points to the inducer. A fan that runs but the furnace does not proceed points to the pressure switch or a blocked port.
What it means: Pressure switch tubing and ports can be cleaned, but the switch itself and the inducer are technician parts. Do not bypass the pressure switch under any circumstance.
6. The thermostat is not actually calling for heat, or the heat pump is in defrost
This is worth ruling out before opening the furnace. A thermostat set to cool, a schedule that has not switched over, or a heat pump in defrost mode all produce a running blower with cool air. On a heat pump, defrost runs for a few minutes and is normal.
How to test it: Set the thermostat to heat and raise the setpoint five degrees above room temperature. Listen for the furnace to start within a minute. On a heat pump, wait ten minutes and see whether the air warms.
What it means: If nothing starts, the thermostat or its wiring is the suspect. If the furnace starts and then stops, go back to the burner checks.
Quick diagnosis table
| What you observe | Most likely cause | Effort |
|---|---|---|
| Blower runs, air cool, filter filthy | Clogged filter | Free |
| Burners light then go out after a few seconds | Flame sensor | Low |
| No glow at all before the burners | Igniter | Low to medium |
| High-efficiency unit, water in the trap | Condensate blockage | Low |
| Inducer does not start | Inducer motor or pressure switch | Technician |
| Nothing starts at all | Thermostat or wiring | Low |
When to stop and call a technician
Call a technician for anything past the filter, the flame sensor, and the igniter: inducer motors, pressure switches, gas valves, heat exchangers, and flue work. Call immediately if you smell gas, see a yellow or lifted flame, or find soot around the burners.
Never run a furnace with the burner compartment open, and never tape a pressure switch closed. Carbon monoxide is the reason those parts exist.
If the furnace locks out three times in a row, stop resetting it. Repeated lockouts usually mean a gas supply problem or a failing gas valve, and each reset puts unburned gas into the heat exchanger.
Related reading
For no hot water, see no hot water. For an air conditioner that runs without cooling, see AC not cooling.