Kitchen
Gas Stove Burner Won't Light: 6 Checks Before You Call Anyone
One burner, all burners, or the igniter clicking with no flame? The pattern tells you whether it is a clogged cap, a wet igniter, or a gas supply issue.
A gas burner that will not light is usually a small, fixable problem: a wet igniter, a clogged cap, or a burner head that has shifted. But gas deserves respect, so the checks below stay on the safe side of the burner and never touch the gas line itself.
The pattern matters. If one burner fails and the others work, the problem is at that burner. If all burners fail but the oven works, the issue is the cooktop’s gas supply or the ignition system. If nothing works and you smell gas, stop reading and act.
Before you touch anything
If you smell gas: do not flip switches, do not light anything, do not use a phone in the room. Open windows, get everyone out, and call your gas utility or 911 from outside. A gas smell is never a DIY situation.
Do not disassemble the gas valve, the regulator, or the supply line. Burner caps, burner heads, grates, and igniters are homeowner-serviceable. The gas manifold is not.
Never use a match or a lighter to light a burner that should ignite electronically. If gas has been flowing, you can get a flash of flame. Fix the igniter instead.
Wait a few minutes after a failed attempt before trying again, so unburned gas can disperse.
1. The burner cap or head is wet or misaligned
This is the most common cause after cleaning. Water or cleaning spray sits between the burner head and the cap, and the spark cannot ignite the gas because the gap is flooded. A cap that has been replaced slightly off-center does the same thing.
How to test it: Remove the grate and the cap, dry everything thoroughly with a cloth, and check that the cap sits flat with no gap. Look at the burner head’s slots for water or residue.
What it means: Dry and reassemble, then try again. After cleaning a gas cooktop, always let it air dry for an hour before use; this prevents most of these calls.
2. The igniter is dirty, wet, or cracked
The igniter is the small ceramic electrode near the burner. It sparks to light the gas. Grease, cleaner residue, or moisture on the electrode weakens or shorts the spark. A cracked ceramic body stops it entirely.
How to test it: Press the ignition and watch the igniter. A healthy one produces a strong, consistent blue-white spark at the gap. A weak, intermittent, or orange spark indicates a dirty or failing electrode. Clean it gently with a dry toothbrush and check the ceramic for cracks.
What it means: Clean and dry the electrode, then test. If the spark is still weak, or the ceramic is cracked, replace the igniter. They are inexpensive and usually a screw-in or clip-in part.
3. The gas is not reaching that burner
If the igniter sparks but no flame appears, the burner is not getting gas. Usually this is a clogged burner head, but on some cooktops each burner has its own jet or orifice.
How to test it: Remove the cap and head and look at the burner base. A visible blockage in the slots or the orifice is the clue. Compare with a working burner: the flame should appear within a second or two of the spark.
What it means: Clean the slots with a straightened paper clip or a small brush. Do not poke anything into the orifice; the brass jet is easily damaged and the size is calibrated. If cleaning does not restore gas flow, call a technician rather than probing the jet.
4. The flame sensor or the re-ignition module has failed
Better cooktops re-ignite automatically if a flame blows out. That function relies on a flame sensor. On some models, a failed sensor prevents ignition entirely; on others, the burner lights but will not stay lit when you release the knob.
How to test it: Light the burner and hold the knob in for ten seconds, then release. If the flame dies when you release, the sensor or the valve’s thermocouple is not confirming flame.
What it means: This varies a lot by brand. On sealed-top models with electronic ignition, the module is usually a replaceable part; on models with a thermocouple, that is the part to change. If the burner will not stay lit after that, stop and call a technician.
5. The spark module or its wiring is failing
If no burner sparks, or the spark is weak at every burner, the module that generates the spark is the common factor. A wet control area after cleaning can also short the module.
How to test it: Listen for the clicking with the knob turned. Clicking at one burner but not others points to that burner’s electrode. No clicking anywhere points to the module, the wiring, or the power supply to the ignition system.
What it means: Modules are replaceable, and the part is usually under the cooktop. If the range is a slide-in with a sealed top, access may require removing the cooktop, which is a technician job on many brands.
6. The gas supply valve or the regulator (stop here)
The shut-off valve behind the range may be partly closed after a move or a repair. A regulator that has failed can starve the cooktop while the oven still works, since they draw at different rates.
How to test it: Check that the valve behind the range is fully open, in line with the pipe. If the oven works and the cooktop does not, note that, then stop.
What it means: Do not adjust the regulator. Call a licensed gas technician. Regulator and manifold work is restricted in most jurisdictions, and an incorrect adjustment can produce incomplete combustion and carbon monoxide.
Quick diagnosis table
| What you observe | Most likely cause | Effort |
|---|---|---|
| One burner, weak or no spark | Dirty or wet igniter | Free |
| Spark present, no flame at one burner | Blocked burner head or jet | Low |
| Just cleaned the cooktop, nothing lights | Water in the burner or igniter | Free, dry it |
| Lights but dies when knob released | Flame sensor or thermocouple | Medium |
| No clicking anywhere | Spark module or wiring | Medium |
| Oven works, all cooktop burners fail | Gas supply to cooktop | Technician |
When to stop and call a technician
Stop for anything involving the gas line, the regulator, the manifold, or a burner that will not hold a flame after a sensor replacement. Stop immediately if you smell gas or if the flame is yellow and sooty rather than blue; incomplete combustion produces carbon monoxide.
Call also if the cooktop has a sealed burner design and the module is under the glass; removing a sealed top without the service manual risks cracking it.
Related reading
For an oven that will not heat, see oven won’t heat. For uneven baking with a working oven, see oven not baking evenly.