Kitchen
Oven Won't Heat: Electric and Gas Checks That Actually Work
The oven lights up but never gets hot, or it heats on one setting only. Here is how to test an electric bake element or a gas igniter safely.
An oven that will not heat is usually a single failed component, and the type of oven determines which one. Electric ovens use resistive elements, and there are usually two: a bake element at the bottom and a broil element at the top. Gas ovens use an igniter and a safety valve. The failure patterns are almost diagnostic on their own.
Before buying anything, note two details: does the broil setting work while bake does not, and does the oven eventually get warm after ten or fifteen minutes? Those two answers split the list below in half.
Before you touch anything
Switch off the breaker that feeds the oven. Do not rely on the control panel being off; on many ranges the elements have power whenever the range is plugged in, and the control board only switches one leg.
For a gas oven, do not attempt any repair on the burner or the gas valve beyond replacing the igniter. If you smell gas at any point, leave the area, ventilate, and call your gas utility or a licensed technician.
Never test an element by touching it during a cycle, and never use the oven’s self-clean cycle to “reset” a broken element. Self-clean runs at 800°F or higher and will finish off a marginal part.
1. The bake element has burned out (electric)
This is the most common electric oven failure. The element is a coil inside a metal tube, and when the coil breaks, the circuit opens. Often you can see the break: a blister, a burnt spot, or a section that looks darker than the rest.
How to test it: With the breaker off, remove the element’s two screws at the back of the oven cavity or the base, and pull the element forward enough to reach the terminals. Disconnect the leads and measure resistance. A healthy element reads roughly 15 to 30 ohms. An open reading means replacement.
What it means: If the broil element works and bake does not, and the bake element measures open, you have found it. Elements are inexpensive and this is a genuinely easy repair: two screws and two wires.
2. The broil element has failed (electric)
If bake works and broil does not, the top element is the suspect. Broil elements fail less often because they run less, but they fail the same way.
How to test it: Same procedure as above, at the top of the cavity. Measure across the terminals with the breaker off. An open circuit confirms it.
What it means: Same easy replacement. Note that some ovens use the broil element during preheat as well, so a failed broil element can make the whole oven seem slow.
3. The oven temperature sensor or thermostat has drifted
The control board regulates temperature using a sensor, usually a small probe with a resistance that changes with heat. If that sensor reads wrong, the oven may heat weakly or overshoot and then cut out.
How to test it: Check the oven’s actual temperature with an oven thermometer placed in the center of the middle rack, and compare it to the setpoint after 20 minutes. A consistent offset of more than 25°F suggests a sensor problem. Sensor resistance should be measured at room temperature and compared to your model’s table.
What it means: Sensors are cheap but the calibration table matters. If you do not have the tech sheet, this check belongs to a technician. Note that many ovens let you recalibrate the offset in the control menu, which is worth trying before replacing hardware.
4. The control board relay has failed
The board switches power to the elements through relays. A stuck-open relay means the element never gets power even though the display looks normal. A stuck-closed relay means the element runs constantly and the oven overheats, which is a genuine fire risk.
How to test it: If the display works, the timer works, and the element measures good but never receives power, suspect the relay. Listen for a click from the board a few seconds after you start a bake cycle. No click usually means no switching.
What it means: Board replacement is a plug-in job on most ranges, but the part can cost a third of a new range. Check the relay’s solder joints for a burnt spot before ordering; sometimes a $5 relay and some solder is the whole repair, if you can solder.
5. The gas igniter is weak or dead (gas)
Gas ovens light with a hot-surface igniter, a small ceramic element that glows orange. The igniter also acts as a safety device: the gas valve will not open until the igniter draws enough current, which means a weak igniter can glow without ever opening the valve.
How to test it: Start a bake cycle and watch the igniter through the oven window or with the door open for the first minute. It should glow bright orange within 30 to 60 seconds and the burner should light shortly after. An igniter that glows dull red, or takes two minutes, is failing even though it is not dead.
What it means: This is the classic gas oven symptom: the igniter glows, you hear no whoosh, and the oven never heats. Replace the igniter with the exact model. Do not substitute a universal igniter; the current draw is calibrated to the valve.
6. The gas supply or the safety valve is the problem (gas)
If the igniter glows brightly and the burner still does not light after 60 seconds, the gas is not reaching the burner. Possible causes: the shut-off valve behind the range is partly closed, another gas appliance was installed and the line was not purged, or the safety valve has failed.
How to test it: Confirm the range’s gas valve is fully open, and check that the cooktop burners light. If the burners work, gas is present at the range.
What it means: Stop here. Do not disassemble the safety valve or the manifold. A gas valve that does not open after a known-good igniter is installed is technician work, and in most jurisdictions it is legally restricted.
7. The oven is in a demo, Sabbath, or lockout mode
Before you buy a part, rule this out. Some ovens ship in a showroom demo mode where the display works but the elements never energize. Others enter a Sabbath mode that holds temperature, or a control lockout after a power interruption.
How to test it: Hold the cancel or clear button for three to five seconds, then power the range off at the breaker for a full minute and back on. Check the manual for the demo-mode exit sequence, which is often a specific button combination held for several seconds.
What it means: If the oven works after a hard reset, the earlier failure may have been a one-time control glitch. Watch it for a week before trusting it.
Quick diagnosis table
| What you observe | Most likely cause | Effort |
|---|---|---|
| Bake dead, broil works (electric) | Bake element open | Low |
| Broil dead, bake works (electric) | Broil element open | Low |
| Element tests good, no power at element | Control board relay | Medium |
| Oven heats but runs 25°F+ off | Temperature sensor or calibration | Low to medium |
| Gas: igniter glows dull, no flame | Weak igniter | Medium |
| Gas: igniter glows bright, no flame | Gas supply or safety valve | Technician |
| Nothing works, display normal | Demo, Sabbath, or lockout mode | Free |
When to stop and call a technician
Call a pro for anything involving the gas manifold, the safety valve, or a smell of gas. Call also if the control board is integrated with the cooktop and the replacement requires reconfiguring settings you cannot access.
Stop immediately if you see arcing, a burnt wire, or a melted terminal at the element connection. That indicates a loose connection that has been heating up, and it can start a fire inside the cabinet.
Self-clean cycles are hard on ovens. If the failure happened right after a self-clean, mention that to the technician; the high heat stresses elements, sensors, and board solder joints all at once.
Related reading
Uneven baking with a working element is a different problem: see oven not baking evenly. For a gas cooktop burner that will not light, see gas stove burner won’t light.