Kitchen
Range Hood Not Venting: Why Your Kitchen Still Smells
Smoke lingers, the hood roars but sucks nothing, or grease collects on the cabinets. Six causes, from a clogged filter to a duct that recirculates.
A range hood has one job: move air out of the kitchen. When it fails, you get smoke that hangs, cooking smells that stay for hours, and a sticky film on the cabinets above the stove. The hood may sound loud and still be doing almost nothing.
Two numbers matter. The hood’s capture area and its airflow in cubic feet per minute. Most residential hoods move 150 to 400 CFM, and a kitchen that recirculates filtered air moves far less than a kitchen that vents outside.
Before you touch anything
Turn off power at the breaker before opening the hood. Range hoods combine grease, heat, and 120-volt wiring, which is a bad combination to troubleshoot live.
Do not vent a hood into a wall cavity or an attic. That is a fire hazard and a code violation. If the duct does not go outside, the hood is recirculating, and no filter will fix grease.
Clean the filter before you test anything else. A grease-saturated filter is the most common cause of weak venting, and it is free to fix.
Turn the fan on and hold a tissue against the filter. If the tissue is not pulled toward it, airflow is the problem, not smell.
1. The grease filter is saturated
Mesh or baffle filters trap grease. When they are coated, air cannot pass. The fan runs, the noise is normal, and almost nothing moves.
How to test it: Remove the filter and hold it up to a light. If you cannot see through the mesh, it is blocked. A baffle filter with grease filling the slots is the same problem.
What it means: Wash the filter in hot water with degreaser, or run it through the dishwasher if the manufacturer allows. Mesh filters need cleaning every month or two; baffle filters last longer but still clog.
2. The duct is blocked, crushed, or too small
This is the most common hidden cause. Flexible duct crushed behind a cabinet, a duct that terminates in a wall, or a duct run that is too small for the hood’s airflow all starve the fan. Birds and lint can block a roof cap.
How to test it: Trace the duct from the hood to the exterior. Confirm it ends at a wall or roof cap that opens freely. Check for crushed sections, especially where the duct bends behind cabinets. Look at the cap from outside.
What it means: Replace flexible duct with rigid metal duct. Keep the run as short and straight as possible, and match the duct size to the hood’s specification, usually 6 inches for a 300 CFM hood. A 4-inch duct cannot support a strong hood no matter what the fan does.
3. The hood is recirculating, not venting
Many hoods are installed in recirculating mode because venting would require cutting through a wall. In that mode, air passes through a charcoal filter and returns to the kitchen. It removes some odors and no grease.
How to test it: Look above the hood for a duct. If there is none, and the hood has a vent at the top or the front, it is recirculating. Check the manual or the model number.
What it means: A recirculating hood will never perform like a vented one. Options: vent it outside if the structure allows, upgrade to a higher-CFM recirculating hood with a fresh charcoal filter, or accept that it is a supplement to opening a window.
4. The blower wheel is dirty or the motor is weak
Grease builds on the blower wheel until it is unbalanced and inefficient. The hood gets louder and moves less air. A failing motor produces the same result.
How to test it: With the power off, remove the filter and look at the blower wheel. A heavy grease coating is obvious. Spin the wheel by hand; it should turn freely. A wheel that wobbles means the hub is worn.
What it means: Clean the wheel with degreaser. If the motor hums without spinning, the capacitor or the motor has failed, and hood motors are replaceable.
5. The hood is mounted too high or too far from the cooking surface
Capture depends on distance. A hood mounted more than 30 inches above the cooktop loses most of its capture, especially for a gas range. An island hood needs more airflow than a wall hood because it captures from all sides.
How to test it: Measure from the cooktop surface to the hood’s lowest edge. Electric and gas ranges usually want 24 to 30 inches. Over 36 inches, capture drops sharply.
What it means: Lower the hood if the duct and cabinet layout allow. On an island, a wider hood with higher CFM is the usual answer.
6. The duct termination is fighting the wind, or the cap is undersized
A roof cap that faces the prevailing wind, or a wall cap with a flap that sticks, cuts effective airflow. In a windy climate, a hood that works on calm days and fails on windy ones is telling you the termination is the problem.
How to test it: Go outside and check the cap while the hood runs. The flap should open fully. A stuck flap or a cap full of lint is a clear cause.
What it means: Replace the cap with a proper model, and clear the lint. On windy sites, a cap with a backdraft damper helps.
Quick diagnosis table
| What you observe | Most likely cause | Effort |
|---|---|---|
| Fan runs, tissue not pulled in | Clogged filter | Free |
| Loud fan, weak suction, duct hidden | Blocked or crushed duct | Medium |
| No duct above the hood | Recirculating installation | Design issue |
| Grinding or humming, no airflow | Blower wheel or motor | Medium |
| Weak capture only at high mount | Hood mounted too high | Medium |
| Works on calm days only | Duct termination or cap | Low |
When to stop and call a contractor
Call a contractor if venting requires cutting through a wall or roof, if the duct runs through an attic or a garage where code requires specific materials, or if the hood’s wiring is not on a dedicated circuit.
Stop if you find grease buildup inside the duct near the hood. A duct fire is a real risk, and a grease-packed duct should be replaced or professionally cleaned.
One maintenance note: clean the filter monthly and the blower wheel yearly. Most “the hood stopped working” calls are a filter that has not been washed in two years and a duct that has never been checked.
Related reading
For a gas burner that will not light, see gas stove burner won’t light. For an oven that heats unevenly, see oven not baking evenly.