Plumbing
Toilet Running Constantly: Fix It Before It Costs You $200
A toilet that keeps refilling is usually a flapper or a fill valve, and both cost under $20. Here is the five-minute diagnosis and the fix.
A toilet that runs for a few seconds every ten minutes is the most expensive free repair in a house. A leaking flapper can waste hundreds of gallons a day, and it is invisible: no puddle, no sound during the day, just a faint hiss at night.
The repair is genuinely simple. Almost every running toilet is either a flapper that no longer seals or a fill valve that no longer shuts off. Both parts cost less than a takeout dinner.
Before you touch anything
Shut off the water at the supply valve behind the toilet, usually a small oval knob on the left. Turn it clockwise until it stops. If it is seized, shut off the house main.
Flush once to empty the tank, and sponge out the remaining water so you can work without soaking your hands.
Do not use chemical dye tablets that stay in the tank if you have a well or a water softener; use food coloring instead. It does the same job and it is harmless.
1. The flapper is not sealing
The flapper is the rubber flap at the bottom of the tank. It lifts to flush and drops to seal. Over time it hardens, warps, or gets a coating of minerals, and water leaks past it into the bowl. That leak triggers the fill valve, which is the refill you hear.
How to test it: Put a few drops of food coloring in the tank, wait fifteen minutes without flushing, and look in the bowl. Color in the bowl means the flapper is leaking. Also look at the flapper itself: a warped edge, a mineral crust, or a chain that is too tight holding it slightly open.
What it means: Wipe the flapper and its seat with a cloth first. If the leak continues, replace the flapper. They are cheap and come in a few standard sizes; take the old one to the store if you are unsure.
2. The fill valve is not shutting off
If the tank keeps filling and the water runs into the overflow tube, the fill valve is not closing at the correct level. Sometimes the valve’s float is set too high, or the valve is old and its internal seal has failed.
How to test it: Watch the water level in the tank. It should stop about an inch below the top of the overflow tube. If water runs into the overflow continuously, the valve is not closing or the float is set wrong.
What it means: Adjust the float first; many valves have a screw or a sliding arm. If the water still runs, replace the fill valve. Modern valves are inexpensive and install in fifteen minutes with no tools beyond a wrench.
3. The chain is tangled or caught
A chain that is too long can catch under the flapper and hold it open a fraction of an inch. A chain that is too short holds the flapper up. Both produce a slow, continuous leak that sounds like a running toilet.
How to test it: Open the tank and look at the chain. It should have a little slack when the flapper is closed. Look for a link caught under the flapper’s edge.
What it means: Adjust the clip on the chain so there is slight slack. That is the entire fix.
4. The overflow tube is set too low or the water level is too high
If the water level sits above the top of the overflow tube, water runs down the tube continuously and the bowl refills. This is a setting, not a failure.
How to test it: Mark the water level, flush, and watch where it settles. It should be below the top of the overflow tube, typically an inch below.
What it means: Lower the float or adjust the fill valve. On some valves the adjustment is a screw; on others you slide the float down.
5. The supply valve or the fill tube is leaking
A leak at the supply connection or the fill tube shows as water on the floor, not as a running tank. If your floor is wet, this is the cause.
How to test it: Dry the floor, then watch the supply line and the fill tube during a flush.
What it means: Tighten the compression fitting or replace the fill tube. A cracked fill tube is a two-dollar part.
6. High water pressure is forcing the valve open
House pressure above about 80 psi can overwhelm a fill valve, causing it to creep open. You may hear water running at other fixtures too.
How to test it: A cheap pressure gauge on an outdoor hose bib tells you the house pressure. Above 80 psi is worth addressing.
What it means: A pressure-reducing valve at the main is the fix. This is a plumber’s job, but it protects every appliance in the house, including the water heater and the dishwasher.
Quick diagnosis table
| What you observe | Most likely cause | Cost |
|---|---|---|
| Color appears in the bowl after 15 minutes | Flapper leaking | Under $10 |
| Water runs into the overflow tube | Fill valve or float setting | Under $20 |
| Chain hanging slack or caught | Chain adjustment | Free |
| Water level above the overflow top | Float set too high | Free |
| Water on the floor | Supply line or fill tube | Low |
| Running at every fixture | House pressure too high | Plumber |
When to stop and call a plumber
Call a plumber if the shut-off valve will not close, if the tank or the bowl is cracked, or if the flange under the toilet leaks onto the floor. A toilet that rocks when you sit on it usually has a failed wax ring, and that is a bigger job.
Stop if you find water seeping from the base of the toilet. That is a floor-level leak, and it can rot the subfloor and the ceiling below.
One money note: a running toilet that refills every ten minutes wastes roughly 200 gallons a day. Fixing it pays for the parts in the first month.
Related reading
For a dripping faucet, see faucet dripping. For a water heater that leaks, see water heater leaking.