Laundry
Washer Banging and Walking During Spin: 6 Causes
A washer that thumps, walks across the floor, or shakes the wall is usually unbalanced, but worn shocks and springs are the real long-term cause.
A washer that bangs during the spin cycle is telling you something is loose, worn, or unbalanced. New machines do this too, and the sound gets worse over months until the machine walks itself out of the laundry room.
The fix depends on the type of machine. Front-loaders balance the drum with springs and shock absorbers, and top-loaders use a suspension rod system or a floating tub. Both types can also be simply overloaded or sitting on an uneven floor. Start with the free checks.
Before you touch anything
Unplug the washer before you tip it, open it, or reach underneath. There is a drive belt, a motor, and a pump under there, and a tipped machine with water in it will spill.
Drain the drum if it holds water. A full drum weighs over a hundred pounds and turns a simple repair into a back injury.
Do not run a spin cycle with the cabinet open to “watch” the problem. The spinning drum can throw water and loose hardware, and the suspension parts are under load.
1. The load is unbalanced
A single heavy item, like a bath mat, a blanket, or a pair of jeans, can sit on one side of the drum and throw off the balance. Front-loaders are especially sensitive, and they will bang against the cabinet before the control cuts the spin.
How to test it: Stop the cycle, open the door, and redistribute the load evenly around the drum. Add two or three towels to a small load as ballast. Run a spin-only cycle.
What it means: If the banging stops, the machine is fine and the load was the problem. Wash bulky items alone or with a couple of smaller pieces, never with a single heavy item.
2. The washer is not level, or the floor is weak
A machine that rocks on its feet will bang and walk. A wood floor over a crawl space flexes under a spinning front-loader and amplifies the vibration. A laundry room with a tile floor on a joist span can do the same.
How to test it: Push down on each corner of the machine. If it rocks, adjust the leveling feet. Put a torpedo level on the top of the machine and check front-to-back and side-to-side. Then observe the floor while someone runs a spin; visible floor movement means the structure is flexing.
What it means: Level the feet and lock the locknuts. If the floor flexes, add a plywood base or a vibration isolation mat, and consider moving the machine. Do not bolt it to a floor that is already moving.
3. The shipping bolts were never removed
New front-loaders ship with four bolts holding the drum to the cabinet. They must be removed before the first wash. Dealers forget regularly, and the result is violent banging, a destroyed suspension, and sometimes a cracked drum.
How to test it: Look at the back of the machine. The bolt holes are at the four corners of the rear panel. If bolts are still installed, that is your answer. The manual shows where they go and the removal wrench is usually taped to the back.
What it means: Remove them, and inspect the suspension; running with bolts in place can damage the shocks. If they have been in for months and the drum is now loose, budget for suspension parts.
4. The shock absorbers or suspension springs are worn (front-loaders)
Front-loaders hold the drum with two or four shock absorbers and two or more springs. When the shocks lose their damping, the drum bounces against the cabinet at high speed, and the machine walks. This is the classic cause of banging that gets worse over a year.
How to test it: With the machine unplugged, open the door and push down sharply on the top of the drum. A healthy drum rebounds once and settles. A drum that bounces two or three times, or that moves easily with little resistance, has worn shocks. Look at the shocks underneath for oil leakage, which means they are finished.
What it means: Shock replacement is a moderate DIY repair: the machine must be tipped back and the front or bottom accessed. Springs are usually replaced as a set with the shocks on machines over eight years old.
5. The drum bearing is failing
A worn tub bearing makes a rumbling or grinding noise that grows with spin speed, and eventually the drum wobbles enough to bang. You will also see rust streaks from the door area on some front-loaders, because the seal has failed and water has reached the bearing.
How to test it: With the machine empty and unplugged, spin the drum by hand. A healthy drum turns smoothly and quietly. A failing bearing feels rough, and there may be play if you lift the drum’s front edge.
What it means: Bearing replacement requires removing the entire drum assembly and pressing out the bearing. On most machines the labor exceeds the value of an older unit. Get a quote before committing, and price a new machine for comparison.
6. The counterweights or cabinet fasteners are loose
Front-loaders use concrete or cast counterweights bolted to the drum. The bolts can loosen over years, and the weight then knocks against the cabinet. Top-loaders have similar issues with the tub support and the cabinet brace.
How to test it: With the machine unplugged, remove the top or back panel and check the counterweight bolts and the cabinet screws for tightness. Look for a weight with a cracked mount; concrete weights do break.
What it means: Re-tighten with the specified torque and use a thread locker if the manual allows. A cracked counterweight must be replaced, not glued.
Quick diagnosis table
| What you observe | Most likely cause | Effort |
|---|---|---|
| Banging with one heavy item only | Unbalanced load | Free |
| Machine rocks when pushed | Leveling feet or weak floor | Free to low |
| Violent banging from day one | Shipping bolts still in | Free |
| Drum bounces when pushed, oil under machine | Worn shock absorbers | Medium |
| Rumble that grows with speed, drum rough by hand | Tub bearing | High |
| Knock from the cabinet, bolts found loose | Loose counterweight | Low |
When to stop and call a technician
Stop if the drum has visible play, if the machine has leaked and rusted around the door, or if the bearing is failing. On a machine over eight years old, bearing and drum work is generally not worth the cost.
Stop also if the machine has walked and damaged the floor or a wall. Fix the suspension first, then repair the floor; a machine that keeps walking will damage it again.
The cheapest long-term fix for vibration is usually preventive: level the machine, avoid single-item loads, and use a rubber isolation mat on a wood floor.
Related reading
For a machine that drains but will not spin at all, see washer won’t spin. For a leak that appears during the spin cycle, see washer leaking water.