Heating
Water Heater Leaking: Which Leaks Are Fixable and Which Mean Replace
Water under a tank heater can come from a fitting, a valve, or the tank itself. The location of the puddle decides whether you repair or replace today.
A leaking water heater is a same-day problem. Twenty gallons on a basement floor ruins drywall, carpet, and anything stored nearby, and a tank that lets go completely can do it in minutes.
The first job is to identify where the water is coming from, because the answer determines everything else. A leak at a fitting is a $20 repair. A leak from the tank body means the heater is finished and needs replacement before it floods the room.
Before you touch anything
Shut off the cold water inlet at the top of the tank, and switch off power at the breaker for an electric unit or set the gas control to off for a gas unit. A tank that is leaking can also be heating with no water covering the element, which burns the element out in seconds.
Do not drain a hot tank onto yourself. Let it cool, or run hot water at a tap until it is lukewarm before draining.
If water is near the electrical connection or the gas burner, do not touch anything until the power or gas is off. Call a technician if you are not comfortable.
1. The T&P relief valve is weeping
The temperature and pressure relief valve is the safety device at the top or side of the tank. It opens when pressure or temperature gets too high. A valve that drips occasionally is doing its job; a valve that drips constantly either has debris on its seat or the tank is over-pressurized.
How to test it: Look for water at the discharge pipe, which usually runs down the side of the tank to a floor drain or pan. If the valve is dripping, open it briefly by lifting the lever and let it snap shut; sometimes that clears debris. If it keeps dripping, suspect a failed valve or a closed system with no expansion tank.
What it means: A valve that will not stop dripping needs replacement, which is a straightforward job with the water off. But if the valve keeps opening, the real problem is thermal expansion or a failed thermostat, and replacing the valve will not fix it. A closed plumbing system needs an expansion tank.
2. A fitting at the top or the element gasket is leaking
The cold inlet, the hot outlet, and the element gaskets are the common non-tank leaks. A compression fitting that has loosened, a dip tube nut that is weeping, or an element gasket that has hardened all produce a small steady drip.
How to test it: Dry the top of the tank and all fittings, then watch with a flashlight for a minute. Water appears at the fitting itself, not from the tank body. On an electric heater, the element is under the cover plate; a leak there rusts the cover and drips down the side.
What it means: Tighten the fitting gently, or replace the ferrule and the gasket. Element gaskets are inexpensive but require draining the tank below the element, which is more work than it sounds.
3. The drain valve is leaking
The drain valve at the bottom is used for flushing. It is often a plastic valve that cracks, or a brass valve that scales shut and then leaks after someone opens it.
How to test it: Dry the valve and watch it. A drip at the spout or at the valve body means replacement. Do not force a valve that is stuck; you will break it.
What it means: Replacing the drain valve means draining the tank. Hose it to a drain first, and consider replacing the plastic valve with a brass one with a hose thread.
4. Condensation, not a leak
A cold tank in a humid basement sweats. Water on the floor under a tank that has no obvious drip point may be condensation, especially in summer.
How to test it: Dry the tank and the floor, then check again after an hour with no hot water use. Condensation reappears at the same rate regardless of whether the tank is heating. Also check whether the water is cold.
What it means: Condensation is not a fault. Insulating the tank and the pipes reduces it. Do not assume a leak and start replacing parts.
5. The tank body is leaking (replace it)
Rust streaks down the side of the tank, water seeping from under the jacket, or a puddle that keeps returning with no fitting involved all point to a failed tank lining. Steel tanks are glass-lined, and once the lining cracks, the steel rusts through.
How to test it: Wipe the tank dry and watch along the seam at the bottom and around the jacket. A leak from the body usually shows as a rust-colored stain and a slow seep that never stops. Look at the bottom of the tank for a rust line.
What it means: A leaking tank cannot be repaired. Shut off the water and the power or gas, drain it, and arrange replacement. Do not wait; a tank that is weeping can let go entirely.
6. The pan or the floor drain is backing up
If the heater sits in a metal pan with a drain line, water in the pan may be coming from a blocked pan drain, not the heater. A floor drain that is backed up produces water around the base of the unit.
How to test it: Dry the pan and pour a cup of water into it. If it does not drain away, the line is blocked.
What it means: Clear the pan drain. Also confirm the pan drain is not routed uphill, which is a common bad installation.
Quick diagnosis table
| Where the water appears | Most likely cause | Action |
|---|---|---|
| Drip at the T&P discharge pipe | Relief valve or over-pressure | Test valve, check expansion tank |
| Drip at the top fittings | Loose fitting or bad gasket | Tighten or reseal |
| Drip at the element cover | Element gasket | Replace gasket, drain below element |
| Drip at the bottom valve | Drain valve | Replace valve |
| Water on the floor, cold, tank dry | Condensation | Insulate |
| Rust stain and seep from the tank body | Failed tank lining | Replace the heater |
| Water in the pan, heater dry | Blocked pan drain | Clear the drain |
When to stop and call a technician
Call a licensed plumber for gas valve or flue work, for a relief valve that keeps opening after a valve replacement, and for any tank replacement you are not comfortable doing yourself. Water heaters are heavy, and a full tank weighs over 400 pounds.
Stop and shut everything off if water reaches the burner assembly or the electrical junction. Call an electrician or gas technician after the water is stopped.
Replace, do not repair, if the tank is over ten years old and leaking from the body, or if the heater is in a location where a failure would flood a finished room. The cost of a new heater is usually less than the water damage.
Related reading
If the heater is not leaking but produces no hot water, see no hot water. For a furnace that runs without heat, see furnace not blowing heat.