Heating

No Hot Water: Diagnosing a Water Heater That Stopped Heating

Cold showers usually come down to a tripped breaker, a failed element, a bad thermocouple, or a pilot that will not stay lit. Six checks in order.

Hot water disappears in two ways. It fails completely and instantly, which usually means an electrical or gas fault, or it fades gradually over weeks, which usually means a failing element or a buildup of sediment. How the failure happened is the fastest way to narrow the cause.

The checks below assume a standard tank water heater. Tankless units have a different failure set and are covered at the end.

Before you touch anything

For an electric heater, switch off the double-pole breaker at the panel and confirm with a non-contact voltage tester at the heater’s junction box. Water heater circuits are usually 240 volts and 30 amps, and the upper element sits live whenever the breaker is on.

For a gas heater, do not attempt to repair the gas valve, the pilot assembly’s gas line, or the venting. You can safely relight a pilot per the manufacturer’s label, and you can replace a thermocouple on many older units, but anything involving gas piping is licensed work.

If you smell gas, leave the house and call the gas utility from outside. Do not flip switches or use a phone inside the house.

Tank temperature above 120°F will scald. If you drain the tank for any reason, let it cool first.

1. The breaker has tripped or the heater has no power

This is the first thing to check and the most common cause of a sudden total loss of hot water in an electric home. Water heater breakers are double-pole, and they trip to a middle position that can look like “on” from a distance.

How to test it: Open the panel and look at the breaker. If the handle sits between on and off, reset it firmly. Then check the heater’s junction box with a voltage tester; if there is no voltage with the breaker on, the circuit has a fault.

What it means: If the breaker trips again immediately, stop and call an electrician. A water heater that trips a breaker has a shorted element or a wiring fault, and repeated resets will damage the breaker.

2. The high-temperature limit switch has tripped (electric)

Electric heaters have a resettable high-limit switch above the upper thermostat. When the tank overheats, usually because a thermostat stuck closed, the switch opens and cuts power to both elements. It has a small red button.

How to test it: With the breaker off, remove the upper access panel and the insulation. The limit switch is the small device with a button. If the button is popped out, press it in.

What it means: A reset that restores hot water means a thermostat is sticking. Have the thermostat replaced; the limit will keep tripping otherwise, and the tank can overheat.

3. The heating element has burned out (electric)

Water heaters have one or two screw-in elements. Over time the element’s sheath corrodes or the internal wire breaks. A failed upper element gives you a tank of lukewarm water; a failed lower element gives you hot water that runs out fast.

How to test it: With power off and the tank drained below the element level, disconnect the element’s wires and measure resistance. A healthy 240-volt element typically reads 10 to 16 ohms. An open reading means replacement. Also check for a short to ground with the meter on the ohms setting between terminal and the tank.

What it means: Elements are inexpensive and replacing one is a 30-minute job with an element wrench. Do not test or replace an element with water in the tank covering it while energized; and never power the heater with the tank empty, because the element will burn out instantly.

4. The thermostat has failed

The upper thermostat controls the upper element and then hands off to the lower thermostat. A thermostat that reads wrong keeps the element from running long enough, so you get warm water instead of hot.

How to test it: With power off, check continuity across the thermostat terminals at room temperature; most are closed when cold. A thermostat that reads open with a cold tank has failed.

What it means: Thermostats are inexpensive. Replace both if they are old; they usually age together.

5. The pilot light will not stay lit (gas)

Gas tank heaters use a standing pilot or an electronic ignition. With a standing pilot, the thermocouple generates a small voltage that holds the gas valve open. When the thermocouple fails, the pilot lights and then goes out as soon as you release the button.

How to test it: Follow the lighting instructions on the tank. If the pilot goes out when you release the knob after holding it for a full minute, the thermocouple is the usual suspect. Look at the pilot flame: it should be blue and envelop the thermocouple tip. A weak yellow flame means a dirty pilot orifice.

What it means: A thermocouple replacement is a reasonable DIY job on older heaters where the pilot assembly is accessible. If the heater has an electronic igniter and a blinking status light, look up the code on the label; those codes point to the specific component.

6. The tank is full of sediment

Hard water deposits build on the tank bottom and around the lower element. Sediment insulates the element from the water, so the element overheats, the recovery time lengthens, and eventually the element fails. You will hear popping and crackling from the tank as water boils under the sediment.

How to test it: Open the drain valve at the bottom into a bucket. If the first water out is brown or full of white flakes, sediment is the issue. Listen for the popping sound during recovery.

What it means: Drain and flush the tank annually. If the heater is more than ten years old and the sediment is thick, flushing may not recover capacity. Replacement is usually the better spend.

7. The dip tube has broken (older tanks)

The dip tube delivers cold water to the bottom of the tank. When it breaks off, cold water enters at the top and mixes with the hot water outlet, so hot water lasts only a few minutes.

How to test it: The symptom is specific: hot water for one or two minutes, then lukewarm, every time, with normal heating recovery. On some tanks the dip tube can be checked by removing the cold inlet fitting.

What it means: Dip tube replacement is possible on tanks where the fitting is accessible. On a tank past its service life, replace the unit.

Quick diagnosis table

What you observeMost likely causeEffort
No hot water at all, suddenTripped breaker or limit switchLow
Lukewarm throughoutUpper element or thermostatMedium
Hot water runs out fastLower element, sediment, or dip tubeMedium
Gas: pilot lights then diesThermocoupleMedium
Popping and crackling during recoverySediment buildupLow to flush
Breaker trips repeatedlyShorted element or wiringElectrician

When to stop and call a technician

Call a licensed plumber or gas technician for gas valve work, venting problems, or a pilot that will not stay lit after a thermocouple replacement. Call an electrician for a breaker that trips repeatedly or a circuit that tests dead.

Call immediately if the tank is leaking from the body rather than a fitting. A leaking tank cannot be repaired, and it can flood a basement. Shut off the water inlet and the power or gas, then arrange replacement.

Tankless units: a sudden loss of hot water there is usually a flow sensor, a scale buildup in the heat exchanger, or an error code from the unit. Those are manufacturer-specific, and the display code is the first thing to read.

If the heater is leaking rather than cold, see water heater leaking. For a furnace that runs without producing heat, see furnace not blowing heat.

Safety first. Unplug the appliance or switch off the breaker before opening anything. If a repair involves gas piping, the main electrical panel, or sealed refrigerant, stop and call a licensed technician.